|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
October 6th, 2004, 06:15 PM
|
|||
|
|||
Linked table manager-Office 2003
I have Office 2003 but need to keep a database in the
2000 format. When I go to linked table manager, it does not show any of the linked tables, however, if I 'Select All' and 'Prompt for a location', then it processes all the tables. The linked table manager works fine on the same database on a computer that is running Office 2000. The problem is I need to unselect a couple linked tables but I can't see them to unselect. Any help would be much appreciated. Micael S. Montoya 
|
|
#2
October 6th, 2004, 09:12 PM
|
|||
|
|||
|
See if this link helps:
BUG: List of currently linked tables may not appear in Linked Table Manager Wizard in a database in Access 2003: http://support.microsoft.com/?id=835519 -- Jeff Conrad Access Junkie Bend, Oregon "Michael" wrote in message ... I have Office 2003 but need to keep a database in the 2000 format. When I go to linked table manager, it does not show any of the linked tables, however, if I 'Select All' and 'Prompt for a location', then it processes all the tables. The linked table manager works fine on the same database on a computer that is running Office 2000. The problem is I need to unselect a couple linked tables but I can't see them to unselect. Any help would be much appreciated. Micael S. Montoya
|
|
#3
December 30th, 2004, 10:29 PM
|
|||
|
|||
|
When I try to register the ACCWIZ.DLL I get a message LoadLibrary
("C:\Program") failed Load module cannot be found. I found the key mentioned in the article in the Class_Root and changed the InProcSvr to the path of the version 11 accwiz.dll, still do luck. I noticed that version said version 8 in reged however. "Jeff Conrad" wrote: See if this link helps: BUG: List of currently linked tables may not appear in Linked Table Manager Wizard in a database in Access 2003: http://support.microsoft.com/?id=835519 -- Jeff Conrad Access Junkie Bend, Oregon "Michael" wrote in message ... I have Office 2003 but need to keep a database in the 2000 format. When I go to linked table manager, it does not show any of the linked tables, however, if I 'Select All' and 'Prompt for a location', then it processes all the tables. The linked table manager works fine on the same database on a computer that is running Office 2000. The problem is I need to unselect a couple linked tables but I can't see them to unselect. Any help would be much appreciated. Micael S. Montoya
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Microsoft Office 2003, Addons, other 16,000 more CDs, [ no dongles, no activations, etc ... needed ! ] | athens.gr. | General Discussions | 1 | September 3rd, 2004 02:43 AM |
| Will I lose Access 2002 if I install Office 2003 | Mark | Setup, Installing & Configuration | 5 | September 1st, 2004 05:51 PM |
| Office 2003 / Office XP Shortcut Bar | Marc Bressman | Setup, Installing & Configuration | 6 | June 26th, 2004 08:42 AM |
| Office 2003 / Office XP Shortcut Bar | Marc Bressman | General Discussions | 6 | June 26th, 2004 08:42 AM |
| Two versions again-language issue | Otto | Setup, Installing & Configuration | 3 | May 28th, 2004 04:57 AM |
Linear Mode
