|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
September 6th, 2004, 03:07 AM
|
|||
|
|||
How can i get the printale area same as specified in the printer..
I have a table. IN the preview, i can see the 8.5x 17 (ROWS) but the cells
are empty after 14" ? 
|
|
#2
September 6th, 2004, 09:26 AM
|
|||
|
|||
|
Two things to check:
One possibility is that the table is wrapped. If Text wrapping is enabled, Word won't allow the table to continue on following pages; instead, its bottom will disappear off the page. Place the cursor inside a cell and choose TableTable Properties. Click the Table tab. Is "Text wrapping" set to "Around"? If it is, click "None", and then click OK. Another possibility is that the text which you can't see in Print Preview has been formatted with the hidden attribute. In Print Layout view, select the text that doesn't display in the print preview, and choose FormatFont. Click the Font tab. Is the "Hidden" option checked? If it is, clear the option and click OK. -- Stefan Blom "Tonyb13" wrote: I have a table. IN the preview, i can see the 8.5x 17 (ROWS) but the cells are empty after 14" ?
|
|
#3
September 6th, 2004, 09:26 AM
|
|||
|
|||
|
Two things to check:
One possibility is that the table is wrapped. If Text wrapping is enabled, Word won't allow the table to continue on following pages; instead, its bottom will disappear off the page. Place the cursor inside a cell and choose TableTable Properties. Click the Table tab. Is "Text wrapping" set to "Around"? If it is, click "None", and then click OK. Another possibility is that the text which you can't see in Print Preview has been formatted with the hidden attribute. In Print Layout view, select the text that doesn't display in the print preview, and choose FormatFont. Click the Font tab. Is the "Hidden" option checked? If it is, clear the option and click OK. -- Stefan Blom "Tonyb13" wrote: I have a table. IN the preview, i can see the 8.5x 17 (ROWS) but the cells are empty after 14" ?
|
|
#4
September 6th, 2004, 09:26 AM
|
|||
|
|||
|
Two things to check:
One possibility is that the table is wrapped. If Text wrapping is enabled, Word won't allow the table to continue on following pages; instead, its bottom will disappear off the page. Place the cursor inside a cell and choose TableTable Properties. Click the Table tab. Is "Text wrapping" set to "Around"? If it is, click "None", and then click OK. Another possibility is that the text which you can't see in Print Preview has been formatted with the hidden attribute. In Print Layout view, select the text that doesn't display in the print preview, and choose FormatFont. Click the Font tab. Is the "Hidden" option checked? If it is, clear the option and click OK. -- Stefan Blom "Tonyb13" wrote: I have a table. IN the preview, i can see the 8.5x 17 (ROWS) but the cells are empty after 14" ?
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Printer disappears when default is set to a network printer | Tony | General Discussion | 1 | June 10th, 2004 12:20 PM |
| Default Printer Problems | Ella | Setting Up & Running Reports | 1 | June 7th, 2004 12:01 AM |
| Access XP - Changing a Printer Designation in PrintRecord Command Button | Abby | Setting Up & Running Reports | 1 | May 26th, 2004 01:58 PM |
Linear Mode
