If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Conditional Formating using Bolding
Does anyone know a solution to this problem
I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted -----Original Message----- On Tue, 22 Jun 2004 06:20:19 -0700, Stan wrote: I have a memo field that I have set the Condition to if Field One is "yes" format the memo field to bold. The field in the report is set to Can Shrink and Can Grow. The Bolding works based on condition, but when the report prints the end of the field truncates. sometimes as much as entire line. When I change the contional format to a background shade instead of Bolding everything prints correctly. It is peferable to Bolding and not shading in this app. Is there a way to fix this problem? You set the Memo field to Can Grow. Did you also set the Detail Section to Can Grow? I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted |
#2
|
|||
|
|||
Conditional Formating using Bolding
Bolding increases the width of a text field. Try
increasing the width. Jim -----Original Message----- Does anyone know a solution to this problem I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted -----Original Message----- On Tue, 22 Jun 2004 06:20:19 -0700, Stan wrote: I have a memo field that I have set the Condition to if Field One is "yes" format the memo field to bold. The field in the report is set to Can Shrink and Can Grow. The Bolding works based on condition, but when the report prints the end of the field truncates. sometimes as much as entire line. When I change the contional format to a background shade instead of Bolding everything prints correctly. It is peferable to Bolding and not shading in this app. Is there a way to fix this problem? You set the Memo field to Can Grow. Did you also set the Detail Section to Can Grow? I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted . |
#3
|
|||
|
|||
Conditional Formating using Bolding
I tried increases the width on the field and on the report
with the same result. The entire last line cuts off. When I remove the bolding and change it to Italics, it works withcutting off any lines -----Original Message----- Bolding increases the width of a text field. Try increasing the width. Jim -----Original Message----- Does anyone know a solution to this problem I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted -----Original Message----- On Tue, 22 Jun 2004 06:20:19 -0700, Stan wrote: I have a memo field that I have set the Condition to if Field One is "yes" format the memo field to bold. The field in the report is set to Can Shrink and Can Grow. The Bolding works based on condition, but when the report prints the end of the field truncates. sometimes as much as entire line. When I change the contional format to a background shade instead of Bolding everything prints correctly. It is peferable to Bolding and not shading in this app. Is there a way to fix this problem? You set the Memo field to Can Grow. Did you also set the Detail Section to Can Grow? I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted . . |
#4
|
|||
|
|||
Conditional Formating using Bolding
Check your TextBox control's Margin props and make sure they are all 0.
-- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "Stan" wrote in message ... I tried increases the width on the field and on the report with the same result. The entire last line cuts off. When I remove the bolding and change it to Italics, it works withcutting off any lines -----Original Message----- Bolding increases the width of a text field. Try increasing the width. Jim -----Original Message----- Does anyone know a solution to this problem I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted -----Original Message----- On Tue, 22 Jun 2004 06:20:19 -0700, Stan wrote: I have a memo field that I have set the Condition to if Field One is "yes" format the memo field to bold. The field in the report is set to Can Shrink and Can Grow. The Bolding works based on condition, but when the report prints the end of the field truncates. sometimes as much as entire line. When I change the contional format to a background shade instead of Bolding everything prints correctly. It is peferable to Bolding and not shading in this app. Is there a way to fix this problem? You set the Memo field to Can Grow. Did you also set the Detail Section to Can Grow? I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted . . |
#5
|
|||
|
|||
Conditional Formating using Bolding
All text Box Margins are set to 0
-----Original Message----- Check your TextBox control's Margin props and make sure they are all 0. -- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "Stan" wrote in message ... I tried increases the width on the field and on the report with the same result. The entire last line cuts off. When I remove the bolding and change it to Italics, it works withcutting off any lines -----Original Message----- Bolding increases the width of a text field. Try increasing the width. Jim -----Original Message----- Does anyone know a solution to this problem I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted -----Original Message----- On Tue, 22 Jun 2004 06:20:19 -0700, Stan wrote: I have a memo field that I have set the Condition to if Field One is "yes" format the memo field to bold. The field in the report is set to Can Shrink and Can Grow. The Bolding works based on condition, but when the report prints the end of the field truncates. sometimes as much as entire line. When I change the contional format to a background shade instead of Bolding everything prints correctly. It is peferable to Bolding and not shading in this app. Is there a way to fix this problem? You set the Memo field to Can Grow. Did you also set the Detail Section to Can Grow? I have tried it both ways with the same result. I use italic with the correct results. I can use Italic and underline with the correct results. I cannot use Bold, if I use Bold the last line is deleted . . . |
Thread Tools | |
Display Modes | |
|
|