If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Bullet Levels in Master
I want to set up a master template where the first bullet level is used for a
subtitle, no bullet and no indent. The second bullet level I want to be the same as the subheading i.e. not bullet and no indent but a different colour. Then I want 3 levels of bullets. I can set up the top level to be as I want – removing the bullet seems to remove the indent as well. I can also remove the bullet on the second level OK. However, when I remove the indent it of course turns it into level one so it can’t then have a different colour by default. I have tried dragging the “square” on the horizontal ruler to position it where I want it but I cannot drag it to be in the same place as the markers for level one, which is what I want. I have inherited another template which does have the markers on the ruler in the same place for level one and level two. How is this done? I am using 2003. |
#2
|
|||
|
|||
Mary Ann,
Have you tried ctrl+dragging the carets thinghies. You can put the carets on top of level 1. Luc "Mary Ann" schreef in bericht ... I want to set up a master template where the first bullet level is used for a subtitle, no bullet and no indent. The second bullet level I want to be the same as the subheading i.e. not bullet and no indent but a different colour. Then I want 3 levels of bullets. I can set up the top level to be as I want - removing the bullet seems to remove the indent as well. I can also remove the bullet on the second level OK. However, when I remove the indent it of course turns it into level one so it can't then have a different colour by default. I have tried dragging the "square" on the horizontal ruler to position it where I want it but I cannot drag it to be in the same place as the markers for level one, which is what I want. I have inherited another template which does have the markers on the ruler in the same place for level one and level two. How is this done? I am using 2003. |
#3
|
|||
|
|||
Yes it works as long as I move the downward pointing triangle first and
that’s just fine! You are a genius – thank you! "Luc" wrote: Mary Ann, Have you tried ctrl+dragging the carets thinghies. You can put the carets on top of level 1. Luc "Mary Ann" schreef in bericht ... I want to set up a master template where the first bullet level is used for a subtitle, no bullet and no indent. The second bullet level I want to be the same as the subheading i.e. not bullet and no indent but a different colour. Then I want 3 levels of bullets. I can set up the top level to be as I want - removing the bullet seems to remove the indent as well. I can also remove the bullet on the second level OK. However, when I remove the indent it of course turns it into level one so it can't then have a different colour by default. I have tried dragging the "square" on the horizontal ruler to position it where I want it but I cannot drag it to be in the same place as the markers for level one, which is what I want. I have inherited another template which does have the markers on the ruler in the same place for level one and level two. How is this done? I am using 2003. |
#4
|
|||
|
|||
Glad I could help!
Luc "Mary Ann" schreef in bericht ... Yes it works as long as I move the downward pointing triangle first and that's just fine! You are a genius - thank you! "Luc" wrote: Mary Ann, Have you tried ctrl+dragging the carets thinghies. You can put the carets on top of level 1. Luc "Mary Ann" schreef in bericht ... I want to set up a master template where the first bullet level is used for a subtitle, no bullet and no indent. The second bullet level I want to be the same as the subheading i.e. not bullet and no indent but a different colour. Then I want 3 levels of bullets. I can set up the top level to be as I want - removing the bullet seems to remove the indent as well. I can also remove the bullet on the second level OK. However, when I remove the indent it of course turns it into level one so it can't then have a different colour by default. I have tried dragging the "square" on the horizontal ruler to position it where I want it but I cannot drag it to be in the same place as the markers for level one, which is what I want. I have inherited another template which does have the markers on the ruler in the same place for level one and level two. How is this done? I am using 2003. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Master Slide Bullet Levels | jblake48 | Powerpoint | 3 | May 4th, 2005 01:49 AM |
inserting a outline into Power Point | Reisville, NC | Powerpoint | 11 | March 12th, 2005 10:43 PM |
My Access query doesn't pull all required records | Nolzgirl | Running & Setting Up Queries | 4 | January 27th, 2005 12:13 AM |
Bullets and Numbers | Becca | General Discussion | 4 | December 12th, 2004 09:55 PM |
a custom bullet style I can't get rid of | Larry | New Users | 4 | June 9th, 2004 11:18 AM |