|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
February 19th, 2010, 06:22 PM
posted to microsoft.public.access.forms
|
|||
|
|||
Problem with sizing Sub Forms on tabbed forms
Hi,
I have an existing application that was designed with several seperate forms. They now want to convert that to a tabbed interface. I have sized the forms uniformly such that they all fit the tabbed control pages. When I load them onto the tabbed pages though they all show differently. Some show large white margins on the bottom but do not show the whole form. Others show similar effects on the right side. Am I missing some magic setting?? Thanks Frustrated 
|
|
#2
February 19th, 2010, 07:12 PM
posted to microsoft.public.access.forms
|
|||
|
|||
|
Problem with sizing Sub Forms on tabbed forms
The subform is sitting in a holder. You want to re-size the holder, not the
subform. Go out to the edge and click and you will see the movement buttons on the edge of the holder. -- Milton Purdy ACCESS State of Arkansas "kc-mass" wrote: Hi, I have an existing application that was designed with several seperate forms. They now want to convert that to a tabbed interface. I have sized the forms uniformly such that they all fit the tabbed control pages. When I load them onto the tabbed pages though they all show differently. Some show large white margins on the bottom but do not show the whole form. Others show similar effects on the right side. Am I missing some magic setting?? Thanks Frustrated .
|
|
#3
February 19th, 2010, 07:20 PM
posted to microsoft.public.access.forms
|
|||
|
|||
|
Problem with sizing Sub Forms on tabbed forms
Hi Milton,
Is that the "Page" of the tab control? Thx Kevin "golfinray" wrote in message ... The subform is sitting in a holder. You want to re-size the holder, not the subform. Go out to the edge and click and you will see the movement buttons on the edge of the holder. -- Milton Purdy ACCESS State of Arkansas "kc-mass" wrote: Hi, I have an existing application that was designed with several seperate forms. They now want to convert that to a tabbed interface. I have sized the forms uniformly such that they all fit the tabbed control pages. When I load them onto the tabbed pages though they all show differently. Some show large white margins on the bottom but do not show the whole form. Others show similar effects on the right side. Am I missing some magic setting?? Thanks Frustrated .
|
|
#4
March 20th, 2010, 09:53 PM
posted to microsoft.public.access.forms
|
|||
|
|||
|
Problem with sizing Sub Forms on tabbed forms
"kc-mass" connearney_AT_comcast_DOT_net wrote in message ... Hi, I have an existing application that was designed with several seperate forms. They now want to convert that to a tabbed interface. I have sized the forms uniformly such that they all fit the tabbed control pages. When I load them onto the tabbed pages though they all show differently. Some show large white margins on the bottom but do not show the whole form. Others show similar effects on the right side. Am I missing some magic setting?? Thanks Frustrated
|
|
#5
March 23rd, 2010, 09:12 PM
posted to microsoft.public.access.forms
|
|||
|
|||
|
Problem with sizing Sub Forms on tabbed forms
"kc-mass" connearney_AT_comcast_DOT_net wrote in message ... Hi, I have an existing application that was designed with several seperate forms. They now want to convert that to a tabbed interface. I have sized the forms uniformly such that they all fit the tabbed control pages. When I load them onto the tabbed pages though they all show differently. Some show large white margins on the bottom but do not show the whole form. Others show similar effects on the right side. Am I missing some magic setting?? Thanks Frustrated
|
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
