If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Problems with Outlook Setup
I have 2 PC's connected thru Wired Ethernet and plugged into hub. The
connection to the Internet is shared thru ICS and connects thru 56k dial up modem. There are 4 users setup on each PC with identical passwords etc. I run Windows XP Professional and Office XP Professional on the host PC (PC1), and Windows XP Home and Office 2000 SBE on the client PC (PC2). When I first install ICS, everything works fine. I then load the Office programs on both PCs and start to have trouble. Outlook XP always sets up the connection when it is installed as connecting thru LAN on my host PC, but it actually connects thru the modem. If I change the connection in Outlook on all users to connect thru modem, then I have a one of the svc. host files that never closes properly and prevents the user profile from loading properly. If I leave the users setup on host as connecting thru LAN then my profile loads properly and all seem fine (I use send and receive to check for mail) except that when I download any files etc from Internet I have to unblock the file because it says that the file was loaded from another computer and therefore is blocked. What is the correct way to setup Outlook with multiple users and 2 PC's that share a dial up internet connection. What am I suppose to set the Outlook connection to on the host PC so it will connect properly thru ICS? It seems that as soon as I load Office on either PC, Outlook takes over the connection and causes problems. |
#2
|
|||
|
|||
Forgot to mention that I am running SP2 update on both PC's.
"Bernard J. Craig" wrote in message ... I have 2 PC's connected thru Wired Ethernet and plugged into hub. The connection to the Internet is shared thru ICS and connects thru 56k dial up modem. There are 4 users setup on each PC with identical passwords etc. I run Windows XP Professional and Office XP Professional on the host PC (PC1), and Windows XP Home and Office 2000 SBE on the client PC (PC2). When I first install ICS, everything works fine. I then load the Office programs on both PCs and start to have trouble. Outlook XP always sets up the connection when it is installed as connecting thru LAN on my host PC, but it actually connects thru the modem. If I change the connection in Outlook on all users to connect thru modem, then I have a one of the svc. host files that never closes properly and prevents the user profile from loading properly. If I leave the users setup on host as connecting thru LAN then my profile loads properly and all seem fine (I use send and receive to check for mail) except that when I download any files etc from Internet I have to unblock the file because it says that the file was loaded from another computer and therefore is blocked. What is the correct way to setup Outlook with multiple users and 2 PC's that share a dial up internet connection. What am I suppose to set the Outlook connection to on the host PC so it will connect properly thru ICS? It seems that as soon as I load Office on either PC, Outlook takes over the connection and causes problems. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Outlook Mail Send Problems | George | General Discussion | 4 | February 13th, 2005 11:17 PM |
setup outlook for multiple users | chevysales | Installation & Setup | 0 | February 3rd, 2005 11:35 PM |
Outlook 2003 and XP SP2 | Joe McCann | Setup, Installing & Configuration | 17 | August 22nd, 2004 04:13 PM |
Outlook 2003 and PocketPC Outlook 2002 | J.C. | General Discussion | 7 | June 28th, 2004 07:20 PM |
Outlook error after moving from Outlook 2003 to Outlook 2002 | Navin | Installation & Setup | 0 | May 13th, 2004 01:51 PM |